收藏本站
LTM8040
PIN FUNCTIONS
LEDA (Bank 1): This pin is the regulated current source
of the LTM8040. Connect the anode of the LED string to
this pin. This voltage must be at least 2.5V for accurate
current regulation.
SHDN (Pin L4): The SHDN pin is used to shut down the
switching regulator and the internal bias circuits. The
2.65V switching threshold can function as an accurate
undervoltage lockout. Pull below 0.3V to shut down the
LTM8040. Pull above 2.65V to enable the LTM8040. Tie
to V IN if the SHDN function is unused.
BIAS (Pin L5): The BIAS pin connects through an internal
Schottky diode to provide power to internal housekeeping
circuits. Connect to a voltage source (usually LPWR or V IN )
greater than 2.6V. Note that this pin is adjacent to the LPWR
pin to ease layout. If this pin is powered by an external
power source, a decoupling cap may be necessary.
LPWR (Pin K5): This is the output of the buck regulator
that sources the LED current. If the LEDA voltage is above
2.6V, connect this pin to BIAS. It is pinned out primarily
for the convenience of the user. If it is not used, leave this
pin ?oating. Please refer to the Applications Information
section for details.
PWM (Pin L7): Input Pin for PWM Dimming Control. A
PWM signal above 1.2V (ON threshold) turns on the output
current source, while a PWM signal below 0.4V shuts it
down. If the application does not require PWM dimming,
then the PWM pin can be left either open (an internal 10μA
source current pulls PWM high) or pulled up to a voltage
V IN (Bank 3): The V IN pin supplies current to the LTM8040’s
internal power converter and other circuitry. It must be lo-
cally bypassed with a high quality (low ESR) capacitor.
ADJ (Pin L3): Use the ADJ pin to scale the LEDA output
current below 1A by either applying a voltage source or by
connecting a resistor to GND. This pin is internally pulled
up to a 1.25V reference through a 5.11k resistor, so ensure
that the voltage source can drive a 5.11k impedance. If
applying a voltage to ADJ, the LEDA current follows the
formula: I LED = 1A ? ADJ/1.25V. If connecting a resistor to
GND, the resistor value should be R = 5.11 ? I LED /(1Amp
– I LED ), where R is in k Ω and I LED is the desired current
out of LEDA in amps. Make sure that the voltage at LEDA
is at least 2.5V.
RT (Pin L2): The RT pin is used to set the internal oscillator
frequency. An 80.6k resistor has already been installed
inside the LTM8040 to default switching frequency to
500kHz. If no modi?cation of the switching frequency is
necessary, leave this pin ?oating. Otherwise, a parallel
resistor applied from RT to GND will raise the switching
frequency. See Table 1 for details.
GND (Bank 2, Pin L1): Tie all GND pins directly to a local
ground plane. These pins serve as both signal and power
return to the LTM8040 μModule, as well as providing
the primary thermal path for heat dissipation within the
unit. See the Applications Information section for more
information about heat sinking and printed circuit board
layout.
source between 1.2V and 10V.
8040fa
6
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LTM8042IV#PBF IC UMODULE LED DRIVER 56LGA
LTM8048MPY#PBF IC DC/DC UMODULE LDO BGA
LTM8052AEV#PBF IC UMODULE 36VIN 5A CVCC 81LGA
M30R224K5 CAP CER 0.22UF 50V 10% RADIAL
M39014/22-0709 CAP CER 1000PF 100V 1% RADIAL
M41L0Q1U JOYSTICK MINI 3AXIS W/BUTTON
M57140-01 CONV DC/DC ISO FOR IPM MOD
M57182N-315 CONV DC/DC HI-VOLT INPUT
相关代理商/技术参数
LTM8040IV#PBF 制造商:Linear Technology 功能描述:DC/DC MICRO MODULE IC
LTM8040IVPBF 制造商:Linear Technology 功能描述:LED Driver 1A 36V Current Source LGA66
LTM8040IV-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 1A μModule LED Driver
LTM8040V 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 1A μModule LED Driver
LTM8042 制造商:LINER 制造商全称:Linear Technology 功能描述:μModule Boost LED Driver and Current Source
LTM8042EV#PBF 功能描述:IC UMODULE LED DRIVER 56LGA RoHS:是 类别:电源 - 板载 >> LED 驱动器 - 恒定电流 系列:LTM8042 产品目录绘图:4015, 7021 Series 标准包装:25 系列:7021 BuckPlus 输入电压:5 ~ 32V 输出电压:2.5 ~ 29.5V 电流 - 输出:700mA 功率（瓦特）:22.4W 安装类型:通孔 端接类型:PCB 引脚 尺寸/尺寸:0.83" L x 0.83" W x 0.43" H（21.1mm x 21.1mm x 10.9mm） 工作温度:-40°C ~ 80°C 类型:降压，带调光 批准:- 其它名称:788-1018
LTM8042EV-1#PBF 功能描述:IC UMODULE LED DRIVER 56LGA RoHS:是 类别:电源 - 板载 >> LED 驱动器 - 恒定电流 系列:LTM8042 产品目录绘图:4015, 7021 Series 标准包装:25 系列:7021 BuckPlus 输入电压:5 ~ 32V 输出电压:2.5 ~ 29.5V 电流 - 输出:700mA 功率（瓦特）:22.4W 安装类型:通孔 端接类型:PCB 引脚 尺寸/尺寸:0.83" L x 0.83" W x 0.43" H（21.1mm x 21.1mm x 10.9mm） 工作温度:-40°C ~ 80°C 类型:降压，带调光 批准:- 其它名称:788-1018
LTM8042EV-1PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:μModule Boost LED Driver and Current Source